Safety Instructions – CSC-Tool PRO


In order to avoid incorrect handling and injury to the user or destruction of the CSC-Tool PRO arising from this, pay attention to the following: A second person is required for the installation of the monitor. Only use the designated carrying handles on the device to move the CSC-Tool PRO. Do not use the handles on the CSC-Tool PRO to transport or unload the device from the pallet. When installing the monitor, observe the specified tightening torque for the M8 bolts (approx. 8-10 Nm). The handles on the CSC-Tool PRO are not carrying handles and are not suitable for lifting the CSC-Tool PRO. The assembly handles on the monitor are intended exclusively for carrying and attaching the monitor. Remove the assembly handles after having attached the monitor. Once the CSC-Tool PRO is damaged, the proper alignment of the vehicle is no longer ensured. In this case the CSC-Tool PRO must not be used anymore and warranty and guarantee will become void. Ensure that the CSC-Tool PRO is secured against rolling by using the brake. Move and align the CSC-Tool PRO only when it is fully retracted. Adjust the height of the monitor only afterwards. Before the height setting of the monitor, ensure that it is in the default setting. The default setting corresponds to the horizontal alignment of the monitor. Sudden forces may occur during the height adjustment of the monitor. To avoid injuries, ensure that no body parts are within the movement area. There is a risk of pinching around the lifting column. Keep hands and fingers away from this area to avoid injuries. When attaching the camera bar, observe the specified tightening torque for the M8 screws (approx. 6 Nm). Pay attention not to pinch hands or fingers when shifting the camera bar. Make sure that the CSC-Tool PRO is properly adjusted every time before starting a camera calibration. Do not look directly into the cameras during operation. Infrared rays are emitted that are invisible to the eye but potentially harmful. Pay attention to firmly attached or connected cables when moving the CSC-Tool PRO. Damages are likely otherwise. Ensure correct seating and secure connection of the power plug. Protect the CSC-Tool PRO from fluids such as water, oil or gasoline. The CSC-Tool PRO and the corresponding components are not waterproof. Do not open the CSC-Tool PRO. Only technicians authorized by Hella Gutmann are allowed to open the device. In case of malfunctions or necessary calibration work and repair steps of the CSC-Tool PRO please contact a technician or trading partner of Hella Gutmann.

In order to avoid incorrect handling and injury to the user or destruction of the CSC-Tool PRO arising from this, pay attention to the following:

A second person is required for the installation of the monitor.
Only use the designated carrying handles on the device to move the CSC-Tool PRO.
Do not use the handles on the CSC-Tool PRO to transport or unload the device from the pallet.
When installing the monitor, observe the specified tightening torque for the M8 bolts (approx. 8-10 Nm).
The handles on the CSC-Tool PRO are not carrying handles and are not suitable for lifting the CSC-Tool PRO.
The assembly handles on the monitor are intended exclusively for carrying and attaching the monitor. Remove the assembly handles after having attached the monitor.
Once the CSC-Tool PRO is damaged, the proper alignment of the vehicle is no longer ensured. In this case the CSC-Tool PRO must not be used anymore and warranty and guarantee will become void.
Ensure that the CSC-Tool PRO is secured against rolling by using the brake.
Move and align the CSC-Tool PRO only when it is fully retracted. Adjust the height of the monitor only afterwards.
Before the height setting of the monitor, ensure that it is in the default setting. The default setting corresponds to the horizontal alignment of the monitor.
Sudden forces may occur during the height adjustment of the monitor. To avoid injuries, ensure that no body parts are within the movement area.
There is a risk of pinching around the lifting column. Keep hands and fingers away from this area to avoid injuries.
When attaching the camera bar, observe the specified tightening torque for the M8 screws (approx. 6 Nm).
Pay attention not to pinch hands or fingers when shifting the camera bar.
Make sure that the CSC-Tool PRO is properly adjusted every time before starting a camera calibration.
Do not look directly into the cameras during operation. Infrared rays are emitted that are invisible to the eye but potentially harmful.
Pay attention to firmly attached or connected cables when moving the CSC-Tool PRO. Damages are likely otherwise.
Ensure correct seating and secure connection of the power plug.
Protect the CSC-Tool PRO from fluids such as water, oil or gasoline. The CSC-Tool PRO and the corresponding components are not waterproof.
Do not open the CSC-Tool PRO. Only technicians authorized by Hella Gutmann are allowed to open the device.
In case of malfunctions or necessary calibration work and repair steps of the CSC-Tool PRO please contact a technician or trading partner of Hella Gutmann.