Start Guided Calibration

For functional principle and mode description see section Guided Calibration.

Proceed as follows:

NOTICE

Remote control

The diagnostic device is remote-controlled by the CSC-Tool PRO. The diagnostic device finishes the remote control automatically after the completion of the diagnostic or calibration procedure of the CSC-Tool PRO.

Connection of the diagnostic device
Connect the diagnostic device (e.g. mega macs X, mega macs S 20 or mega macs PLUS) to the vehicle (see section Connection of the Diagnostic Device).
NOTICE! All steps and safety-relevant notes for connection and handling of the diagnostic device are written down in the user manual of the prevailing diagnostic device (e.g. mega macs X, mega macs S 20 or mega macs PLUS); they shall be followed accordingly.
Start of guided calibration

Select >Guided calibration<.
All available diagnostic devices are indicated.
Select the requested device and select >Connect<.
Select >Continue< after successful connection.

Select vehicle
The following options are available for the vehicle selection:
New selection:

Option 1: Automatic vehicle selection through VIN readout with the help of the connected diagnostic device
Option 2: Search and select vehicle manually through VIN or HSN/TSN
Option 3: Select vehicle through Manufacturer > Series > Model > Suspension.

Previously selected vehicles:

Select the vehicle directly from the overview or use the search and filter function.

Suspension selection:

Select the suspension for newly selected vehicles and vehicles processed last.
Select >Continue<.

Optional: Do a trouble code request
Options:

Select >Skip<

Select >Execute<

When having selected >Execute<:
The trouble codes of the vehicle are read out and displayed on the left of the Cali-OS.

The list contains all existing trouble codes with status.
A trouble code can be touched to indicate detailed information (description, potential causes, diagnostic notes).
Single faults or all faults can be deleted with .
When required you can repeat the trouble code request with >Repeat trouble code request<.

Select calibration type
Select the calibration type and proceed with >Continue<. NOTICE! The CSC-Tool PRO controls the connected diagnostic device. If needed make entries directly in the diagnostic device.
Check the required hardware for the selected calibration
Check if the indicated hardware is complete and ready for operation and confirm with >Continue<.
Select reason for calibration
Select the applicable reason and confirm with >Continue<.
Confirm preconditions
Check the preconditions indicated in the Cali-OS by using the checklist.
Confirm fulfilled points by activating the check boxes and select >Continue<.
Measure height of wheel arch edges
Measurement can be done with the following methods:
Measurement with Bluetooth laser distance meter:

>Select measurement device<
Switch on the laser distance meter.
Select the device from the list > Connect > and close the window with >Back<.
Determine the measurement point: Measure from highest point of wheel arch edge to the floor.
Start measurement: Briefly push >DIST< on the laser distance meter, then push briefly >DIST< again.
Measurement is saved.
The value is instantly indicated on the screen.
Repeat the procedure for all four wheels.

Select >Continue< after having completed the measurement.
Manual measurement:

Measure the height of the wheel arch edges.
Enter the measured values in the Cali-OS.

Select >Continue< after having completed the measurement.
Attach wheel clamps & 3D panels

Position the CSC-Tool PRO in front of the vehicle.
Attach the wheel clamps and 3D panels and level them (see section Attaching the wheel clamps).

Select >Continue< if the 3D panels are exactly vertical.
Register the position three-dimensionally
Move the vehicle forwards and backwards according to the instructions in the Cali-OS, until the three-dimensional position has been captured.
If the 3D panels are captured successfully, select >Continue<.
Confirm safety precautions
Apply the parking brake and confirm with >Applied<.
Align the CSC-Tool PRO
NOTICE! The monitor shall be in standard alignment position. The default setting corresponds to the horizontal alignment of the monitor.

Align the CSC-Tool PRO centered and parallel in front of the vehicle.
NOTICE
Position the CSC-Tool PRO in a way that distance, parallelism and centering correspond to the nominal values in the Cali-OS display.
Operate the left and right brakes with the foot.
Select >Continue<.

Then:

Adjust the height of the monitor with the lower button in the Cali-OS (push button and keep pushed to adjust the height automatically).
Select >Continue<.

Perform calibration
The reference panel is automatically indicated on the monitor.
Start the calibration with >Continue<.
NOTICE! Calibration is in progress. Please follow the instructions in the diagnostic device.
The results are indicated after successful completion of the process.
Proceed with >Continue<.
Optional: Perform a second trouble code request.
You can perform another trouble code request (>Execute< or >Skip<).
Save protocol
To save the protocol in the Car History, enter the VIN and kilometer/mileage reading and select >Save<.
You can skip this step if necessary.
NOTICE! Here the protocol is indicated in the next steps but it is not saved in the Car History.
Complete the calibration
Select >Completed< to complete the procedure.
The calibration protocol is indicated.
Optional:

You can print out the protocol with >Print<:
Select the protocol content and proceed with >Continue<.
Enter all the data that shall appear on the protocol printout and confirm with >Continue<.
or
Send the protocol with >Send< to the stored e-mail address:
Select the protocol content and proceed with >Continue<.
Enter all the data that shall be included in the protocol and confirm with >Send<.